CERNroot - Revision history

Chris: /* Configuration of CERNroot */

2016-03-11T10:34:16Z

Configuration of CERNroot

← Older revision		Revision as of 10:34, 11 March 2016
Line 1:		Line 1:
	[[Category:software-faq]]		[[Category:software-faq]]
	== Configuration of ~~CERNroot~~ ==		== Configuration of CernRoot ==
	Running the command '''root-setup cern''' will configure your system to use ~~CERNroot~~. This command will also automatically create or change your '''.bashrc''' file, so after you have run this command your system is almost ready, you do have to re-open the terminal to activate the new environment settings or run the '''source''' command given at the end of set-up.		Running the command '''root-setup cern''' will configure your system to use CernRoot. This command will also automatically create or change your '''.bashrc''' file, so after you have run this command your system is almost ready, you do have to re-open the terminal to activate the new environment settings or run the '''source''' command given at the end of set-up.

	The following directory is automatically created:<br/>		The following directory is automatically created:<br/>

Chris: /* Configuration of CERNroot */

2016-03-07T11:45:13Z

Configuration of CERNroot

← Older revision		Revision as of 11:45, 7 March 2016
Line 4:		Line 4:

	The following directory is automatically created:<br/>		The following directory is automatically created:<br/>
	'''/home/p123456/fair_install/~~cernroot~~/'''		'''/home/p123456/fair_install/CernRoot/'''

	After the configuration is finished, you can test your '''root''' by simply running the command:		After the configuration is finished, you can test your '''root''' by simply running the command:
	'''root'''		'''root'''

Chris at 14:03, 3 February 2016

2016-02-03T14:03:38Z

← Older revision		Revision as of 14:03, 3 February 2016
Line 1:		Line 1:
	[[Category:software-faq]]		[[Category:software-faq]]
	== Configuration of CERNroot ==		== Configuration of CERNroot ==
	Running the command '''root-setup cern''' will configure your system to use CERNroot. This command will also automatically create~~-adapt~~ your '''.bashrc''' file, so after you have run this command your system is almost ready, you do have to re-open the terminal to activate the new environment settings or run the '''source''' command given at the end of set-up.		Running the command '''root-setup cern''' will configure your system to use CERNroot. This command will also automatically create or change your '''.bashrc''' file, so after you have run this command your system is almost ready, you do have to re-open the terminal to activate the new environment settings or run the '''source''' command given at the end of set-up.

	The following directory is automatically created:<br/>		The following directory is automatically created:<br/>

Chris at 10:52, 23 April 2015

2015-04-23T10:52:14Z

← Older revision		Revision as of 10:52, 23 April 2015
Line 1:		Line 1:
	[[Category:software-faq]]		[[Category:software-faq]]
	== Configuration of ~~CERN-ROOT~~ ==		== Configuration of CERNroot ==
	~~If you only need ordinary~~ '''root''', ~~then just pick either r3b~~, ~~fair, cbm~~ or ~~panda and follow~~ the ~~installation instructions~~. ~~Afterwards, your system~~ is automatically ~~configured for ordinary CERN-ROOT as well.~~<br/>		Running the command '''root-setup cern''' will configure your system to use CERNroot. This command will also automatically create-adapt your '''.bashrc''' file, so after you have run this command your system is almost ready, you do have to re-open the terminal to activate the new environment settings or run the '''source''' command given at the end of set-up.
	~~Running the command~~ '''~~root-setup <environment>~~''' ~~is probably the easiest way.~~ After the configuration is finished, you can test your root by simply running the command:
			The following directory is automatically created:<br/>
			'''/home/p123456/fair_install/cernroot/'''

			After the configuration is finished, you can test your '''root''' by simply running the command:
	'''root'''		'''root'''

Chris: Created page with "Category:software-faq == Configuration of CERN-ROOT == If you only need ordinary '''root''', then just pick either r3b, fair, cbm or panda and follow the installation inst..."

2015-04-21T12:24:10Z

Created page with "Category:software-faq == Configuration of CERN-ROOT == If you only need ordinary '''root''', then just pick either r3b, fair, cbm or panda and follow the installation inst..."

New page

[[Category:software-faq]]
== Configuration of CERN-ROOT ==
If you only need ordinary '''root''', then just pick either r3b, fair, cbm or panda and follow the installation instructions. Afterwards, your system is automatically configured for ordinary CERN-ROOT as well.<br/>
Running the command '''root-setup <environment>''' is probably the easiest way. After the configuration is finished, you can test your root by simply running the command:
'''root'''